how to clean mass air flow sensor ford ranger

1 Install the MAF sensor to the air cleaner assembly and ensure that the retaining clips are fully engaged. Apply the cleaner 10-15 blasts around the inside of the sensor will do.

How To Clean A Ford Maf Sensor Simple Effective Youtube

Place the sensor on a towel for cleaning.

. If the mass air flow sensor on your Ranger should fail or if it needs to be cleaned it can cause very rich or very lean. Air filters are effective at cleaning the air to a certain extent. Avoid physically touching them like with a cotton swab since this could break the hot wires.

Important Suggestions And Tips. The mass air flow sensor or maf sensor on your ford ranger measures the mass flow rate of the air that is entering the engine. Often the mass airflow sensor really only needs cleaning when they go bad.

All you need is a multimeter. Ford has used a Hot-Wire type mass air flow sensor for many years. When the sensor is dry replace the sensor back in the MAF body and secure with the security star-head screws.

And over time when enough dust accumulates the sensor starts to. Clean the sensor. To do this act delicately but you will just have to disassemble it on both sides of the air duct and disconnect the electrical plug on top of it.

The safest way to clean the MAF sensors hot wires is to just spray them and let them air dry. Instead of letting this problem persist consider a new mass air flow sensor for Ford Ranger from AutoZone. Cleaning the Mass Airflow Sensor.

The title says it all toolsparts you will needflat head screwdriver mass air flow sensor cleanerfrom auto parts store. This is a very simple procedure that involves taking. 3 Attach the engine wiring harness connectors to the IAT and MAF sensors.

After doing this my tru. 1 install the maf sensor to the air cleaner assembly and ensure that the retaining clips are fully engaged. I usually Spray it for 3 seconds then wait a minute.

If the mass air flow sensor isnt working properly then you will be faced with one or more symptoms such as lack of power and bad fuel economy. Let it dry for about 10 minutes before reinstalling. 2 install the air cleaner outlet tube then tighten the outlet tube clamps until snug.

Carefully spray the filaments with electrical cleaner preferably maf cleaner and let it dry thoroughly. 1 install the maf sensor to the air cleaner assembly and ensure that the retaining clips are fully engaged. These dont need to be torqued down just simply hand tight.

Also clean the sides of the part its housing its connectors and its terminals. How To Clean Mass Air Flow Sensor Ford Ranger. Uses mass airflow sensor cleaner.

2 Install the air cleaner outlet tube then tighten the outlet tube clamps until snug. Testing the Ford mass air flow MAF sensor on all of the Ford Lincoln and Mercury cars and trucks is a very simple test that can be done without a scan tool. The job of the mass air flow sensor is to keep track of the amount of air coming in through the air filter so that the ECU can adjust the amount of fuel getting into the engine.

When the vehicle is running dirt and other airborne particles that escape from the air filter can settle on the sensor. This information is sent to the engine computer which uses it to calculate the amount of fuel that is needed for the proper air and fuel mixture. The most common cause of a malfunctioning MAF sensor in Ford Ranger is dirt and grime accumulation on the sensor.

It sure beats the heck out of. This procedure should work on most Ranger Mustang Taurus F150 etc. Carefully wipe the aluminum mount surface of the MAF body if there is any dust there but be careful not to get dust in the mount hole.

This is a bad idea it can ruin the sensor. Lay sensor on a paper towel Inside the opening is where the sensors are Spray it really good. Once taken apart you will have the ability to move forward to the step cleaning the mass air flow sensor of your Ford Ranger.

Its really cheap and available at any parts store. I recommend using a digital multimeter but an analog multimeter can also be used. Cleaning a Ford mass air flow sensor.

Reinstall in reverse order. From the 1990s and 2000s. In this video Ill take you along and show you how I cleaned my MAF sensor on my 2004 Ford Ranger 30L.

The mass air flow sensor or MAF sensor on your Ford Ranger measures the mass flow rate of the air that is entering the engine. If you have a hot wire mass air flow sensor make sure the cleaner doesnt get onto the hot wires or plate. When yours is malfunctioning it means trouble for your fuel economy.

Your air mass information is needed for your engine control unit to correctly balance fuel mass to your engine. Then hit it one more time. Some folks recommend using alcohol because its usually on hand and can clean the sensor.

97 2 3l Sohc Idle Air Control Mass Air Control Senors Location Cleaning Ranger Forums The Ultimate Ford Ranger Resource